logo
Blog
BLOGDETAILS
Zu Hause > Blog >
How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg
Veranstaltungen
Kontakt Mit Uns
Ms. Ivy Deng
86-755-27374847
Wechat BTL_IvyDeng
Kontaktieren Sie uns jetzt

How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg

2026-11-16
Latest company blogs about How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg

When a customer specifies a 4-layer RF board design—20mil RF-35TC on top and bottom, a single 5mil WL-PP280 prepreg in the middle, 1.3mm finished thickness, and 3-4 blind vias—the material selection and stackup rationale are worth examining.

A four-layer board with one prepreg is standard. However, when the dielectric is only 5mil and the outer cores are low-loss PTFE, the process window narrows. This article outlines the material specifications, stackup data, and the rationale behind these selections.

The Material Choice: WL-PP280 vs. FR-4 PP

If a design requires only structural bonding, standard FR-4 prepreg is the common option. However, with RF-35TC (Df 0.002) on both sides, using an FR-4 prepreg (Df 0.015+) in the middle would reduce the low-loss performance of the outer layers.

WL-PP280 is the specified material. According to supplier data, it is a ceramic-filled PTFE film with thermoset resin coatings on both sides and no glass fabric. Its Df is between 0.0017 and 0.0019, which matches RF-35TC. Because it is a PTFE-based system, its thermal expansion is closer to the core material, which helps reduce interface stress during lamination.

How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg

How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg

Processing the 5mil Dielectric and Blind Vias 3-4

The challenge is the combination of a thin 5mil dielectric and blind vias 3-4. The following outlines the manufacturing process.

1. Drilling and Registration
Blind vias 3-4 go from layer 3 to layer 4, passing through the 5mil prepreg and part of the RF-35TC core. Because the dielectric is thin, the vias are shallow, and registration tolerance is tight. The symmetrical stackup (same RF-35TC material top and bottom) keeps stress distribution even during lamination, which supports layer-to-layer alignment.

2. Lamination and Via Filling
To fill the blind vias, the low-flow characteristics of WL-PP280 are used. This prepreg minimizes resin squeeze-out during lamination, keeping the resin in place to fill the vias. After lamination, the blind via areas are cross-sectioned to confirm the fill is solid, without visible voids.

3. Trace Width and Etching
With only 5mil of dielectric, the surface traces need to be narrow to hit the 50Ω target. Narrow traces are more sensitive to etching tolerance. The etching process is adjusted to maintain line width consistency, ensuring the impedance remains within the design window.

Surface Finish: Immersion Gold, No Solder Mask, No Silkscreen
The board uses immersion gold for flatness and to avoid ENIG's nickel-layer loss. There is no solder mask and no silkscreen. Removing the solder mask is standard in RF designs, as it eliminates dielectric effects on surface trace impedance.

Where This Board Fits
This board suits designs with RF traces on the outer layers, power or ground on the inner layers, and interlayer interconnect requirements. The 1.3mm thickness provides mechanical rigidity, and the 47.5mm × 62.4mm size fits modular RF front ends or antenna units.

Conclusion
In RF multilayer design, material matching is as important as individual material performance. A high-performance core material can be selected, but if the prepreg in the middle does not match, the entire stackup performance is compromised.

If you are evaluating a similar RF multilayer stackup, send over the design. We can review the specifications and identify potential manufacturing considerations.

Have you worked with thin dielectric layers and blind vias in RF boards? What challenges did you face?

Blog
BLOGDETAILS
How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg
2026-11-16
Latest company news about How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg

When a customer specifies a 4-layer RF board design—20mil RF-35TC on top and bottom, a single 5mil WL-PP280 prepreg in the middle, 1.3mm finished thickness, and 3-4 blind vias—the material selection and stackup rationale are worth examining.

A four-layer board with one prepreg is standard. However, when the dielectric is only 5mil and the outer cores are low-loss PTFE, the process window narrows. This article outlines the material specifications, stackup data, and the rationale behind these selections.

The Material Choice: WL-PP280 vs. FR-4 PP

If a design requires only structural bonding, standard FR-4 prepreg is the common option. However, with RF-35TC (Df 0.002) on both sides, using an FR-4 prepreg (Df 0.015+) in the middle would reduce the low-loss performance of the outer layers.

WL-PP280 is the specified material. According to supplier data, it is a ceramic-filled PTFE film with thermoset resin coatings on both sides and no glass fabric. Its Df is between 0.0017 and 0.0019, which matches RF-35TC. Because it is a PTFE-based system, its thermal expansion is closer to the core material, which helps reduce interface stress during lamination.

How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg

How to Build a 1.3mm 4-Layer RF-35TC Board with a 5mil Prepreg

Processing the 5mil Dielectric and Blind Vias 3-4

The challenge is the combination of a thin 5mil dielectric and blind vias 3-4. The following outlines the manufacturing process.

1. Drilling and Registration
Blind vias 3-4 go from layer 3 to layer 4, passing through the 5mil prepreg and part of the RF-35TC core. Because the dielectric is thin, the vias are shallow, and registration tolerance is tight. The symmetrical stackup (same RF-35TC material top and bottom) keeps stress distribution even during lamination, which supports layer-to-layer alignment.

2. Lamination and Via Filling
To fill the blind vias, the low-flow characteristics of WL-PP280 are used. This prepreg minimizes resin squeeze-out during lamination, keeping the resin in place to fill the vias. After lamination, the blind via areas are cross-sectioned to confirm the fill is solid, without visible voids.

3. Trace Width and Etching
With only 5mil of dielectric, the surface traces need to be narrow to hit the 50Ω target. Narrow traces are more sensitive to etching tolerance. The etching process is adjusted to maintain line width consistency, ensuring the impedance remains within the design window.

Surface Finish: Immersion Gold, No Solder Mask, No Silkscreen
The board uses immersion gold for flatness and to avoid ENIG's nickel-layer loss. There is no solder mask and no silkscreen. Removing the solder mask is standard in RF designs, as it eliminates dielectric effects on surface trace impedance.

Where This Board Fits
This board suits designs with RF traces on the outer layers, power or ground on the inner layers, and interlayer interconnect requirements. The 1.3mm thickness provides mechanical rigidity, and the 47.5mm × 62.4mm size fits modular RF front ends or antenna units.

Conclusion
In RF multilayer design, material matching is as important as individual material performance. A high-performance core material can be selected, but if the prepreg in the middle does not match, the entire stackup performance is compromised.

If you are evaluating a similar RF multilayer stackup, send over the design. We can review the specifications and identify potential manufacturing considerations.

Have you worked with thin dielectric layers and blind vias in RF boards? What challenges did you face?